New products

Showing 1 - 19 of 19 items
  • New

    RalliTEK's steel spacer lift kits with built-in front alignment correction are ideal for lifting your vehicle without disturbing the factory ride quality. That's right! The front spacers in this kit are offset to maintain the factory range of adjustment that the OEM camber bolt can achieve. The 2.5” rear spacers included in this kit are intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.


    Alignment is still required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!


    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Alignment Corrections Designed Into the Front Spacers
    • Hammered Blue Powdercoat
    • Multi-Link (Rear Subframe) Spacers Included
    • All Hardware Included
    • Includes 1.5" rear subframe spacers to maintain rear ground clearance and an OEM alignment
    • Extended Exhaust Hangers Included


    NOTE:

    NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Subaru
  • New

    RalliTEK's steel spacer lift kits with built-in front alignment correction are ideal for lifting your vehicle without disturbing the factory ride quality. That's right! The front spacers in this kit are offset to maintain the factory range of adjustment that the OEM camber bolt can achieve. The 2.5” rear spacers included in this kit are intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.


    Alignment is still required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!


    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Alignment Corrections Designed Into the Front Spacers
    • Hammered Blue Powdercoat
    • Multi-Link (Rear Subframe) Spacers Included
    • All Hardware Included
    • Includes 1.5" rear subframe spacers to maintain rear ground clearance and an OEM alignment
    • Extended Exhaust Hangers Included


    NOTE:

    NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Subaru
  • New

    RalliTEK's steel spacer lift kits with built-in front alignment correction are ideal for lifting your vehicle without disturbing the factory ride quality. That's right! The front spacers in this kit are offset to maintain the factory range of adjustment that the OEM camber bolt can achieve. The 2.5” rear spacers included in this kit are intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.


    Alignment is still required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!


    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Alignment Corrections Designed Into the Front Spacers
    • Hammered Blue Powdercoat
    • Multi-Link (Rear Subframe) Spacers Included
    • All Hardware Included
    • Includes 1.5" rear subframe spacers to maintain rear ground clearance and an OEM alignment
    • Extended Exhaust Hangers Included


    NOTE:

    NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Subaru
  • New

    RalliTEK's steel spacer lift kits with built-in front alignment correction are ideal for lifting your vehicle without disturbing the factory ride quality. That's right! The front spacers in this kit are offset to maintain the factory range of adjustment that the OEM camber bolt can achieve. The 2.5” rear spacers included in this kit are intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.


    Alignment is still required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!


    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Alignment Corrections Designed Into the Front Spacers
    • Hammered Blue Powdercoat
    • Multi-Link (Rear Subframe) Spacers Included
    • All Hardware Included
    • Includes 1.5" rear subframe spacers to maintain rear ground clearance and an OEM alignment
    • Extended Exhaust Hangers Included


    NOTE:

    NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Subaru
  • New

    RalliTEK's steel spacer lift kits with built-in front alignment correction are ideal for lifting your vehicle without disturbing the factory ride quality. That's right! The front spacers in this kit are offset to maintain the factory range of adjustment that the OEM camber bolt can achieve. The 2.5” rear spacers included in this kit are intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.


    Alignment is still required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!


    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Alignment Corrections Designed Into the Front Spacers
    • Hammered Blue Powdercoat
    • Multi-Link (Rear Subframe) Spacers Included
    • All Hardware Included
    • Includes 1.5" rear subframe spacers to maintain rear ground clearance and an OEM alignment
    • Extended Exhaust Hangers Included


    NOTE:

    NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Subaru
  • New

    RalliTEK's steel spacer lift kits with built-in front alignment correction are ideal for lifting your vehicle without disturbing the factory ride quality. That's right! The front spacers in this kit are offset to maintain the factory range of adjustment that the OEM camber bolt can achieve. The 2.5” rear spacers included in this kit are intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.


    Alignment is still required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!


    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Alignment Corrections Designed Into the Front Spacers
    • Hammered Blue Powdercoat
    • Multi-Link (Rear Subframe) Spacers Included
    • All Hardware Included
    • Includes 1.5" rear subframe spacers to maintain rear ground clearance and an OEM alignment
    • Extended Exhaust Hangers Included


    NOTE:

    NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Subaru
  • New

    RalliTEK's steel spacer lift kits with built-in front alignment correction are ideal for lifting your vehicle without disturbing the factory ride quality. That's right! The front spacers in this kit are offset to maintain the factory range of adjustment that the OEM camber bolt can achieve. The 2.5” rear spacers included in this kit are intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.


    Alignment is still required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!


    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Alignment Corrections Designed Into the Front Spacers
    • Hammered Blue Powdercoat
    • Multi-Link (Rear Subframe) Spacers Included
    • All Hardware Included
    • Includes 1.5" rear subframe spacers to maintain rear ground clearance and an OEM alignment
    • Extended Exhaust Hangers Included


    NOTE:

    NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Subaru
  • New

    RalliTEK's steel spacer lift kits with built-in front alignment correction are ideal for lifting your vehicle without disturbing the factory ride quality. That's right! The front spacers in this kit are offset to maintain the factory range of adjustment that the OEM camber bolt can achieve. The 2.5” rear spacers included in this kit are intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.


    Alignment is still required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!


    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Alignment Corrections Designed Into the Front Spacers
    • Hammered Blue Powdercoat
    • Multi-Link (Rear Subframe) Spacers Included
    • All Hardware Included
    • Includes 1.5" rear subframe spacers to maintain rear ground clearance and an OEM alignment
    • Extended Exhaust Hangers Included


    NOTE:

    NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Subaru
  • New

    RalliTEK's steel spacer lift kits with built-in front alignment correction are ideal for lifting your vehicle without disturbing the factory ride quality. That's right! The front spacers in this kit are offset to maintain the factory range of adjustment that the OEM camber bolt can achieve. The 2.5” rear spacers included in this kit are intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.


    Alignment is still required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!


    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Alignment Corrections Designed Into the Front Spacers
    • Hammered Blue Powdercoat
    • Multi-Link (Rear Subframe) Spacers Included
    • All Hardware Included
    • Includes 1.5" rear subframe spacers to maintain rear ground clearance and an OEM alignment
    • Extended Exhaust Hangers Included


    NOTE:

    NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Subaru
  • New

    This is the bolt used RalliTEK spacer and Lift kits.

    M14 X 1.5 X 200mm Gr 10.9 65mm THREAD LENGTH

    *Sold as a 4 piece set of bolts.

  • New
    Reduced price!

    NOTE: This product exhibits superficial scratches, scrapes, and dents that do not compromise the integrity or its intended purpose.


    Forester Lift Kit

    • Ride Height: +1" LIFT*
    • Spring Rate: 220 lb/in
    • 18-20% stiffer than OEM
    • Fits with OEM and KYB struts
    • Increases street stability and towing capacity
    • Increases off-road performance

    PRICE IS PER PAIR OF SPRINGS.

     

    *Product Disclaimer:

     

    The advertised ride height specified for this product is a measurement taken from a completely stock vehicle. Your vehicle's actual ride height after installing these springs may be more or less dependent on your vehicle's trim package, add-ons, or additional modifications.

    $161.70 $231.00 -30% *}
  • New
    Reduced price!

    NOTE: This product has been damaged during shipping and receiving. This product exhibits minor scratches, dents, scrapes but does not adversely impact this product's integrity nor hinder its intended purpose.


    With a RalliTEK skid plate for your Subaru, you can protect yourself like a WRC champion. No more cringing while driving over hazards, just smile and know the underside of your Subaru is protected!


    ***FLAT RATE SHIPPING WITHIN THE CONTINENTAL USA IS ONLY $49.99. IF YOU ARE OUTSIDE THIS AREA PLEASE EMAIL INFO@RALLITEK.COM OR CALL 503-619-0055 FOR THE BEST SHIPPING QUOTE***


    Have you ever cringed as you drove over a hazard because there was no warning or little option? Road debris can cause expensive damage to the oil pan and other engine components as these parts, made from soft sheet metal that can easily be punctured, causing oil loss and engine damage. A RalliTEK skidplate provides vehicles with an extra layer of protection, effectively shielding vulnerable engine components and oil pans from harm.

    Whenever a factory plastic front plate is damaged or missing, the air is likely, not directed throughout your radiator. Fuel efficiency and mileage, unfortunately, would be compromised. A RalliTEK aluminum skidplate will significantly help to retain factory airflow characteristics maintaining mileage, engine temperature, and airflow. All RalliTEK skidplates are thoughtfully engineered and carefully battle-proven to protect your vehicles' vitals. This item offers low-cost insurance for anyone who may be concerned about the ride height or while making an unexpected detour off-road.

    RalliTEK skidplates are manufactured using the finest light-weight aluminum alloys and precision laser-cut technology for a superior fit and shape. RalliTEK skid plates are designed with a careful balance of light-weight design while remaining resistant to punctures and impacts. All of our RalliTEK Skidplates employ factory existing mounting points for quick and effortless installation or removal. The installation process is carefully elaborated and requires only basic hand tools and a few minutes of your time.

    Our RalliTEK skidplates are proudly built and tested in the USA!

    Subaru
    $284.71 $334.95 -15% *}
  • New
    Reduced price!

    NOTE: This product has been damaged during shipping and receiving. This product exhibits minor scratches, dents, scrapes but does not adversely impact this product's integrity nor hinder its intended purpose. 


    With a RalliTEK skid plate for your Subaru, you can protect yourself like a WRC champion. No more cringing while driving over hazards, just smile and know the underside of your Subaru is protected!

    • New redesign to work with 2.5i AND 3.6R models
    • Hardware included. Bolt-on Install.
    • Available with or without access panels
    • 1/8" thick laser-cut aluminum plate.
    • Uses 4 M8 RalliTEK Dome Washers
    • Use the drop-down to purchase the skid plate without the access panels

    ***FLAT RATE SHIPPING WITHIN THE CONTINENTAL USA IS ONLY $49.99. IF YOU ARE OUTSIDE THIS AREA PLEASE EMAIL INFO@RALLITEK.COM OR CALL 503-619-0055 FOR THE BEST SHIPPING QUOTE***



    Have you ever cringed as you drove over a hazard because there was no warning or little option? Road debris can cause expensive damage to the oil pan and other engine components as these parts, made from soft sheet metal that can easily be punctured, causing oil loss and engine damage. A RalliTEK skidplate provides vehicles with an extra layer of protection, effectively shielding vulnerable engine components and oil pans from harm.

    Whenever a factory plastic front plate is damaged or missing, the air is likely, not directed throughout your radiator. Fuel efficiency and mileage, unfortunately, would be compromised. A RalliTEK aluminum skidplate will significantly help to retain factory airflow characteristics maintaining mileage, engine temperature, and airflow. All RalliTEK skidplates are thoughtfully engineered and carefully battle-proven to protect your vehicles' vitals. This item offers low-cost insurance for anyone who may be concerned about the ride height or while making an unexpected detour off-road.

    RalliTEK skidplates are manufactured using the finest light-weight aluminum alloys and precision laser-cut technology for a superior fit and shape. RalliTEK skid plates are designed with a careful balance of light-weight design while remaining resistant to punctures and impacts. All of our RalliTEK Skidplates employ factory existing mounting points for quick and effortless installation or removal. The installation process is carefully elaborated and requires only basic hand tools and a few minutes of your time.

    Our RalliTEK skidplates are proudly built and tested in the USA!

    Subaru
    $329.33 $387.45 -15% *}
  • New

    The APR Performance Radiator Cooling Plate has been engineered to help reduce under-hood temperatures and to provide your engine bay with the race-inspired looks of carbon fiber. 


    DETAILS:

    • Improve radiator effectiveness
    • Reduce under-hood temperatures
    • Pre-preg. Carbon fiber manufacturing Process: the APR Radiator cooling plates are constructed by high temperature and high pressure pre-preg. carbon fiber production process, making them durable and able to withstand elevated engine bay temperatures
    • Designed for easy installation: the APR Radiator Cooling Plates are designed to factory specifications for easy installation and clean fit and finish
    • Fade resistant epoxy coating: to ensure durability, the APR Radiator Cooling Plate uses fade resistant epoxy coating to reduce the effects of high engine bay temperatures
    • Known for weight savings and durability, APR Performance Radiator Cooling Plates are formed in the autoclave at high temperatures using pre-preg manufacturing processes
    • APR Performance Radiator Cooling Plates are molded to fit specific vehicle applications
    • Mounting holes are included with every APR Performance Radiator Cooling Plate for factory-fit placement
    • Built to take quality to a new level and deliver peak performance
    • Meticulously engineered with top-of-the-line technology
    • Expertly built from super strong yet lightweight materials
    • Thoroughly tested to withstand extreme conditions

    Subaru
  • New

    The APR Carbon Fiber License Plate Frame has been designed to cover the area surrounding the license plate area to provide your exterior with a nice carbon fiber touch.


    DETAILS:

    • Carbon Fiber Manufacturing Process
    • Exterior components are vacuum-bagged and cured in the autoclave at high temperatures, ensuring quality, durability, and extremely high strength-to-weight ratios
    • Exterior components are designed to factory specifications for easy installation and clean fit and finish
    • Built to take quality to a new level and deliver peak performance
    • Meticulously engineered with top-of-the-line technology
    • Expertly built from super strong yet lightweight materials
    • Thoroughly tested to withstand extreme conditions

    Subaru
  • New

    Improve your engine aesthetics by installing this attractive Carbon Fiber Alternator Cover in place of the bland plastic piece.


    FEATURES:

    • Carbon fiber manufacturing process: engine covers are vacuum-bagged and cured in the autoclave at high temperatures, ensuring quality, durability, and extremely high strength-to-weight ratios
    • Fade-resistant clear coat: engine covers are finished with UV-stable, production clear coat paint, then individually hand-polished to a brilliant shine
    • Easy installation: engine covers are designed to factory specifications for easy installation and clean fit and finish
    • Built to take quality to a new level and deliver peak performance
    • Meticulously engineered with top-of-the-line technology
    • Expertly built from super strong yet lightweight materials
    • Thoroughly tested to withstand extreme conditions

    Subaru
  • New

    NOTE: This product may exhibit minor scratches, dents, or scrapes but will not compromise the product's integrity or intended purpose.


    *Damaged during shipping and receiving, never been used.

    *Sold as individual front strut


    Bilstein B6 shock absorbers and struts are the ideal choices for improving the performance of any vehicle. These shock absorbers and struts feature a monotube design that provides consistent fade-free performance. Bilstein B6 shock absorbers and struts utilize a unique, velocity-sensitive, digressive piston that reacts to changing road conditions to provide consistent fade-free performance. All B6 shock absorbers and struts are tuned for each specific application to assure optimal performance is achieved. Bilstein B6 shock absorbers and struts offer a significant improvement in ride quality, handling, and comfort.

    Subaru
  • New

    NOTE: This product may exhibit minor scratches, dents, or scrapes but will not compromise the product's integrity or intended purpose.

    • Damaged during shipping and receiving, never been used.
    • Sold as a single Rear Strut


    Bilstein B6 shock absorbers and struts are the ideal choices for improving the performance of any vehicle. These shock absorbers and struts feature a monotube design that provides consistent fade-free performance. Bilstein B6 shock absorbers and struts utilize a unique, velocity-sensitive, digressive piston that reacts to changing road conditions to provide consistent fade-free performance. All B6 shock absorbers and struts are tuned for each specific application to assure optimal performance is achieved. Bilstein B6 shock absorbers and struts offer a significant improvement in ride quality, handling, and comfort.

    Subaru
  • New

    These are our most aggressive rear lift spacers intended to correct low rear ride height on vehicles with a constant heavy load when overload springs are not enough.

    An alignment is required after installation. Make note that the center of gravity will be raised after installation. You may want to consider pairing these spacers with a set of RalliTEK springs to improve handling both on and off the road!

     

    SPECIFICATIONS:

    • 3/16” MIG Welded Steel Construction
    • Hammered Blue Powdercoat
    • All Hardware Included

    NOTE:

    • DOES NOT INCLUDE SUBFRAME DROP SPACER KIT – REQUIRED TO MAINTAIN FACTORY ALIGNMENT SPECS
    • NOT RECOMMENDED FOR USE WITH 0.75" OR 1” REAR LIFT SPRINGS UNLESS RUNNING A CONSTANT HEAVY OVERLOAD OF 500+LBS (MAY PROVIDE MORE LIFT THAN SUBFRAME SPACERS CAN CORRECT FOR)

    Scion
    Subaru
Showing 1 - 19 of 19 items